AD-S10 KIT (FULL) DEPOSIT TO GET ON LIST
We prefer the deposit method, so we can get you into our system and invoice you. You have the option to send a check or pay online invoice. We contact you personally via email. Once deposit is made you get CONFIRMATION NUMBER, keep that. FILL OUT THE ORDER FORM ALSO, WE NEED THAT. ORDER FORM AND PAYMENT ARE TWO SEPARATE THINGS.
KIT TOTAL IS 1300$ SHIPPED WITH CHECK or BUY IT NOW $1338 (we email invoice) NEED order form filled out on bottom of page.
IF YOU SELECT DEPOSIT OPTION
$1250 IS REMAINING BALANCE IF YOU MAIL CHECK.
IF YOU PAY ONLINE THE REMAINING BALANCE, 3% FEE IS ADDED. (international orders adds cost),
THIS IS A (DEPOSIT) TO START YOUR ORDER, TOTAL DUE AFTER IS $1250. YOU MUST CLICK THE ADD TO CART BUTTON AND PAY ON HERE FOR THE DEPOSIT.
*DEPOSIT IS NON REFUNDABLE IF ANYTHING CHANGES ON YOUR END.
*PA residents must pay 6% sales tax
*INTERNATIONAL ORDERS MUST EMAIL TO GET ON LIST, CURRENTLY IT WILL NOT LET YOU ADD DEPOSIT TO CART.
DON'T FORGET TO FILL OUT THE ORDER FORM BEFORE OR AFTER YOU ADD TO CART THE DEPOSIT. YOU WILL NOT BE ON LIST UNLESS YOU PAY THE 50$ DEPOSIT.
---------PLEASE READ BELOW-------------
KITS IN STOCK.
ONCE YOU ARE ON LIST YOU WILL BE CONTACTED VIA EMAIL TO CONFIRM ORDER. WE CONTACT YOU TO TOUCH BASE. AT THAT TIME YOU CAN MAIL A CHECK OR YOU WILL BE EMAILED A DIGITAL INVOICE (THAT ADDS 3%) ITS A SECURE TRANSACTION. TOTAL DUE BEFORE SHIPMENT WILL BE $1250 WITH CHECK.
DO NOT SEND ANY CHECKS UNTIL WE COMMUNICATE TO DO SO!
PLEASE SUBMIT THE ORDER FORM BELOW AFTER YOU PAY DEPOSIT.
AD-S10 KIT (BODY MOUNTING KIT ONLY) DEPOSIT TO GET ON LIST
KITS IN STOCK
THIS IS A DEPOSIT TO START YOUR ORDER, TOTAL DUE AFTER THIS WILL BE $850. AGAIN THIS IS A DEPOSIT ONLY TO GET ON LIST.
DEPOSIT IS NON REFUNDABLE IF ANYTHING CHANGES ON YOUR END.
PLEASE FILL OUT THE ORDER FORM BELOW AND SUBMIT, AFTER YOU PAY DEPOSIT.
ONCE YOU ARE ON LIST YOU WILL BE CONTACTED PRIOR TO PRODUCTION. AT THAT TIME YOU CAN MAIL A CHECK (KEPT IN OFFICE UNTIL WEEK OF PRODUCTION) OR YOU WILL BE EMAILED A DIGITAL INVOICE (THAT ADDS 3%) ITS A SECURE TRANSACTION. TOTAL DUE BEFORE SHIPMENT WILL BE $850 WITH CHECK.
$900 Shipped. Kits usually in stock. As of May 2025 1 week or less lead.We can expedite any leadtime, just inquire.
This is a body mounting kit ONLY for 47-55.1 Chevy AD truck to S10 2wd Chassis. Works best with the 117.9 Longbed s10 chassis. Short and Ext cab chassis can work but need shortened or lengthened accordingly.
Easily add bumpers, engine or transmission xmember. Just put in notes on the order form and we will quote you a new total.
Whats included?
This is same as full kit only does NOT include engine, trans x, front/rear bumper brackets or firewall booster plate.
-Comes with 4 cab corners with bushings
-6 Running board brackets
-4 corner bed brackets
-Front core support brackets with bushings
-If running a front bumper please let me know, I will include brackets that will bolt to my core support and allow you to adapt stock brackets and or purchase my adjustable bumper brackets that are designed for this setup.
-Comes with grade 8 hardware (cab bolts are 1/2" and are included) Full kit is 15lb worth so this would be a little less, the hardware alone in this body kit costs over 50$.
-Works with all year s10 chassis 2wd.
-Fully Bolts on
-Adjusts 2-6" off frame (all the off frame heights commonly used, 4" being my preferred)
additionally. FULL kit is $1250 shipped. Pricing gets merged with certain parts and shipping.
This is the most economical way to get your build going. You will get instructions and personal support through me. MADE IN USA with USA MATERIALS
*NOTE there is usually a 3% fee if you pay with cc. I prefer a check.
41-46 CHEVY TRUCK KIT
Kit in developement. Motor mounts are 100% and available anytime LS or SBC. Transmission x member is universal and used with the AD kits. 4 cab mounts with some adjustment. Can't go too much bc cabs will bottom out on the frame as they are very narrow. Six running board brackets, core support brackets, 4 corner bed mounts, bushings and hardware included. Rear bumper is same as our AD kits, it may need some minor adjustments.
FRONT bumpers are not going to be added for a little while. Waiting on feedback from customers with cab placement, core support etc. Some instructions are started and should help. Once I get final fitment and specs I can make a full instruction kit and get these fully into production.
As now I charge 950 shipped for everything minus front bumper. If there are things that need changed, I will fix and ship free of charge.
Unfortunately I do not have one of these at the shop, so Im limited on certain things. But its looking promising so far with the help of willing customers.
2026 Truck Calendar
Thanks for supporting USA made product and a genuine truck lover.
**IF PRODUCT IS SOLD OUT PLEASE BE PATIENT UNTIL I RE ORDER MORE OR UPLOAD MORE TO STORE
** ALLOW 1-3 DAYS TO SHIP, THESE WILL SHIP POST OFFICE. IN BLACK POLY MAILER.
** INTERNATIONAL ORDERS MUST CONTACT ME, PLEASE DO NOT ORDER ONLINE.
God bless. Jesus will return.
Contact with any question [email protected]
AD-S10 Motor Mounts (LS version) Click for Details
Typically in stock, if not 1 week or less lead. Please email [email protected]
Stepback and UP mounts. Set your LS engine perfectly in your frame swap build. Designed specifically for AD chevy trucks and s10 chassis. These mounts will also raise engine up in the engine bay, providing some benefits. Main benefit is using the typical truck oil pan, saving you money and time. Another is the appearance in engine bay. Also some extra room to work with headers and exhaust. There is also a stock height setting on my mounts. You can see in one of the pictures. All you have to do is cut the bottom slot off of motor mount to utilize the stock height. Made in USA.
You can use stock truck or car accessories, and of course aftermarket. The stock AC compressor and bracket will not work. The only lower mounted bracket setup I have seen work is from dirty dingo and using a mini sanden compressor, all others mount up top usually work, some dont. Kwick Performance K10700 makes one that won't hit the inner fenders
I supply bushing numbers in invoice. You can get at local parts stores or summit, and jegs.
Comes with upper mounts (to block), stepback plates, and hardware (minus block bolts 8 metric bolts M10 1.5x25). MADE TO ORDER IF NOT IN STOCK.
AD-S10 Motor Mounts (SBC version) Click for Details
CURRENTLY OFFERING WITHOUT BUSHINGS ONLY $110 SHIPPED.
Typically in stock, if not 1 week or less lead. Please email [email protected]
Stepback and UP mounts. Set your SBC engine perfectly in your frame swap build. Designed specifically for AD chevy trucks and s10 chassis. These mounts will also raise engine up in the engine bay, providing some benefits. Main benefit is ability to use a mechanical fuel pump. Another is the appearance in engine bay. Also some extra room to work with headers and exhaust. There is also a stock height setting on my mounts. All you have to do is cut the bottom slot off of motor mount to utilize the stock height. Made in USA.
I supply bushing numbers in invoice. You can get at local parts stores or summit, and jegs.
Comes with upper mounts (to block), stepback plates, and hardware (minus block bolts 6 3/8 x1-16). MADE TO ORDER IF NOT IN STOCK.
4.3 Motor Mounts AD-S10 swap
ONLY OFFERING KIT WITHOUT BUSHINGS CURRENTLY $110 SHIPPED.
The top mounts to block are same as SBC. Uses same bushings as SBC and LS with my setup. Main difference is the baseplates. These use a much larger setback baseplate. As always with my mounts, two height settings. you get bushing part number when you order my mounts.
Comes with upper mounts (to block), setback plates, and hardware (minus 6 block mount bolts).
Made in USA
You can probably use any stock clamshell block mount and use my setback plate and bushings. However my block mounts set engine higher and setback is built into them. Since there is so much room with the v6 engines it won't matter too much. So if you want just setback plates those would be $50 alone.
As of 2024 the 4.3 setback plates have additional holes to accomodate SBC or LS settings. So what that means, if you decide to upgrade to SBC later, you can no problem. You have everything you need with this kit to run a 4.3 or SBC. You can also buy my LS upper mounts and use these setback plates, if you decide to upgrade to LS. Basically this new setback plate is a multi use plate rather than just a 4.3 only.
Base Plates ONLY
Please inquire if you are unsure what you need. Most times using other companies or stock engine mounts (that bolt to block) and use with my baseplates won't always give you the proper setback. The 4.3 and the 41-46 plates are the exception.
If you are doing an SBC or LS ADs10 Swap, you would want my upper mounts that come with baseplates and hardware kit. (They have setback in them also)
4.3 baseplates now have two settings so you can use them with LS and SBC engines by moving the bushings forward on the baseplates. The 41-46 baseplates are the longest I offer and should give you plenty of room with use of most any top motor mount.
The benefit of using my top motor mounts (that bolt to block) is they have two height settings. Most standard LS or SBC motor mounts or kits, are not designed for doing the AD S10 swap or a 41-46 s10 swap.
3 options are standard baseplates used with LS or SBC, 4.3 baseplates, and the 41-46 baseplates. Prices are $50, $60 and $65 shipped.
NO bushings included. NO hardware included. If you want to do a standard LS or SBC swap I highly recommend getting my motor mount kit and not trying to piece together a kit with other top mounts.
1st three photos are 4.3, 2 photos are the 41-46 and the black frame is a standard LS/SBC baseplate.
IF out of stock, just email. Odds are we have some in shop, just not on store page.
41-46 Motor mounts
Swap your SBC or LS in your 41-46 GM build using s10 2wd chassis. NO BUSHINGS included, will supply part number that you can order online or usually get at local part stores. Will come with hardware and plenty of adjustment setback plate. Upper mounts have two height settings. Cut lower hole off if you want to mount engine lower. Laser cut in house, USA material.
Please email if not stocked on store. [email protected]
Extension Kit
THESE ARE STOCKED. $150 SHIPPED. This is a heavy duty kit weighing at 20lbs. This will extend a shortbed S10 chassis 108.9" to my suggested WB of 117". This will require welding. Some of it will bolt on to get you started. Made in house with USA steel. Good to place 1.5" in front of s10 rear cab mount. This will allow my cab landing bracket to set on stock part of frame as seen in pic. Truck pictured is using ext kit. So is the infamous pigpen truck shown here.
THESE ARE TYPICALLY A STOCKED ITEM, EMAIL US TO RECIEVE AN ONLINE INVOICE. [email protected]
PATCH PANELS_INNER TO OUTTER COWL_SET Click for Details
$175 SHIPPED Made in USA.
As of 2025 Im trying to make these more often and take on preorders. These are time consuming to make and Im very proud of these. I have more help in shop now so trying my hardest to have lower to no leads on these. These were my first ever cut and fabbed parts I did back in 2015. When I launched my kits in 2019 these were the first products I started building a name selling right before kits exploded.
I have had a ton of good feedback on the fitment of my inner to outter cowls for the 47-55.1 AD trucks. Don't waste your time with the crappy repops out there. At best to your door those are 125$ and will take you hours to rework. These ship raw. Please contact me and make sure I can make them for you in time. You get LEFT and RIGHT sides. Fender holes are pre cut, sides are flat so no need for more gaps to fill vrs factory style. MADE TO ORDER in the USA [email protected]
Brake Floor Bracket
Floor Brake bracket for s10 swap. With full kits add $50, on its own $65 shipped.
If you are ordering the FULL kit from us, do not purchase this online separately. We can invoice you and ship with kit.
You need to supply pedal assembly and booster. Speedway sells pedal for around 100$
USUALLY IN STOCK EMAIL TO RECIEVE AN INVOICE.
Best to be used at no less than 4" off frame setting. It gets really tight near transmission x member. Pedal often will not land in stock hole in floor, which I recommend gets moved closer to steering column anyway.
email us if out of stock [email protected]
Brake Pedal assembly (firewall)
CLUTCH PEDAL ASSEMBLY SOLD SEPARATELY (ITS ON ITS OWN PAGE) WILL HAVE A BUNDLE OPTIONS FOR BOTH SOON)
IF you have my swap kit (2022 and up era you should have the firewall booster plate.
If you do not, you can add it to cart on this page for $15. I recommend it because these firewalls were not meant for pedals and pressure. They need reinforced.
If you only want a booster plate and try to order it from this page we will direct you to the item link to buy it separately, as it ships on its own that way. If you buy it with the brake assembly it will ship all in one box.
This is a 5.3 to 1 ratio. Made of mostly .188 steel, booster firewall plate is 11g. Pedal bolts together in 2 sections which allows for the ability to space the pedal left or right for specific tuning. This comes in handy when doing an AD s10 swap bc sometimes you want to move the steering column over to the left.
Will come with a brake switch bracket also.
YOU MAY NEED A RETURN SPRING (working on providing those)
Designed to keep brake booster up higher and have good pedal length. If you compare other companies to mine, they have short pedals and don't usually have the brake pedal or brake light switch bracket. Those alone are $60 with other companies.
Can bundle with clutch pedal to save on shipping, email us for an invoice in that case.
These just went into production in May 2025. I usually have some in stock. Please email us for an invoice you can pay online, if sold out. [email protected]
Clutch Pedal
Made to order usually have some in stock, MC not included. I prefer to use. Wilwood GS Compact Master Cylinders 260-15098
Assembly is made from .188 usa steel, tig welded. Pedal arm and foot pedal included. Bolts on for extra adjustment. Most times it will come with a hiem joint. Comes with 1/8" support plate, and brackets for neutral safety switch, price is shipped.
Can bundle with the Brake pedal assembly to save shipping just send us an
email for an invoice [email protected]
Brake/Clutch Combo kit
THIS IS FOR BRAKE PEDAL ASSEMBLY AND CLUTCH PEDAL ASSEMBLY
NO BOOSTER, OR MASTER CYLINDERS INCLUDED.
BRAKE WILL NOT COME WITH PLATE (YOU CAN ADD IT) CLUTCH WILL COME WITH A FIREWALL PLATE.
This is a 5.3 to 1 ratio. Made of mostly .188 steel, booster firewall plate is 11g. Pedal bolts together in 2 sections which allows for the ability to space the pedal left or right for specific tuning. This comes in handy when doing an AD s10 swap bc sometimes you want to move the steering column over to the left.
Will come with a brake switch bracket also.
YOU MAY NEED A RETURN SPRING (working on providing those)
Designed to keep brake booster up higher and have good pedal length. If you compare other companies to mine, they have short pedals and don't usually have the brake pedal or brake light switch bracket. Those alone are $60 with other companies.
DETAILS ON CLUCH IF YOU WANT TO READ, ARE ON THE CLUTCH PAGE BACK IN STORE.
These just went into production in May 2025. I usually have some in stock. Please email us for an invoice you can pay online, if sold out. [email protected]
Brake Booster Firewall Plate
$29 Shipped by itself. As of 2023 these are included FREE in FULL kit orders (if in stock which is most always the case)
This will make mounting an aftermarket or s10 booster much easier. Put the plate on outside of firewall, mark holes and drill. Then weld this plate inside firewall. S10 boosters are slightly different than aftermarket, so that is why there is a slotted hole in one side. So works with aftermarket and s10 boosters.
Measures almost 8x9" and is 11g steel.
Typically in stock, if not be a week or less lead time.
Transmission Xmember_basic MADE TO ORDER
Summer 2022 all trans x basics will be tubular, tig welded, center section 2" longer while C channels 2" shorter. New design is a bit stiffer and better looking. This will move forward and back on chassis to cater to different transmissions. Most common used are 4l60e and 80e. TH350 , 400, 700R, 5 speeds will work also. Once the "C" channels are mounted to frame the center section will slide up or down so you can set your engine degree. Due to the universal design, the smaller trans will need one part shimmed on each c channel. BEST installed with cab lifted or pulled. $175 SHIPPED. In some cases this costs us almost 50$ to ship. There is alot of time and welding that goes into these.
MADE TO ORDER if not listed for sale on store. Please inquire.
AD-S10 CAB MOUNTS (Click for details)
$235 SHIPPED. If you need these, please email us. We have to break up full kits to sell these, that is why we don't stock them on the website.
Comes with 4 cab mounts, urethane bushings and grade 8 hardware. As with my whole kit, these mounts will come shipped at a 4" off frame height (with bushing) and adjust from 2-6" for ultimate ease of setting your desired height. We are the originator of any adjustable swap kit. You have up and down and forward and back adjustment.
The front mounts will come with provisions to accept my running board brackets, or... you can make your own to adapt to my mount. Made in USA with USA steel. Cut and fabbed in house. Save yourself the headache of building your own, looking up measurements and second guessing everything. These are a no brainer even for experienced builders. You will get instructions emailed to you and full support.
Shipped Raw.
Control Arms_S10 1.5 EXTENDED MADE TO ORDER
Made in Batches (Currently for air ride only)
COIL OVER VERSION CURRENTLY MUCH SLOWER PRODUCTION ($1100 for those) I do not recommend aldin america, much harder to fit. Viking seem the easiest to install, Qa1 are good also, Ridetech Im sure would work.
stock spring option to come later.
For now Im only making 50-75 sets a year
I keep a wait list for these, leads have been coming down considerably. Can rush if needed.
1.5" extended, stock wheel location
Tubular arms, Tig welded
Lower Shock tabs welded on
Sway bar link tabs welded on
Custom Cross shafts
Custom bushings
Zerk fittings
Accepts stock s10 ball joints
Custom balljoint cups
Made with strength in mind, yet shaved weight.
Average ship box around 40 lb (40-60$) in cost to ship average
Ships Raw (powder coat may be future option)
Additional options for bag arms (both for $100)
Adjustable shock towers
Sway Bar hiem links
You will need to provide shock bolts and shocks, ball joints, I supply part numbers for everything needed, including steering and ext brake line.
Shock Towers (bolt on adjustable)
Several options. Bolt on with some adjustment (incase you find a different shock) I supply shock number and lower shock bolt number with order. Just the towers with landing brackets are $75 shipped.
1.If only using stock control arms you only need my towers for $75, you would then drill a hole in your LCA and buy a shock bolt and shock.
2.If you have other company's tubular arms that do not have lower shock brackets and or sway bar tabs you would want the $150 option.
3.If you made or have other shock towers and only want the poly links, tabs and lower shock tabs they are $75 shipped.
Shock towers can be welded or bolted on, the sway bar tabs and lower shock brackets need welded on.
If you buy my control arms the shock and sway tabs are already welded on, no matter what.
Usually have these in stock, if you NEED anything more than just towers, email for invoice.
Email with any questions [email protected]
4 link_triangular MADE TO ORDER
Until more trucks are on road, I will keep pricing at 1500 plus ship. Once more feedback is in. Price will most likely be 1800 plus ship. I may also offer some other items like diff bolts, shocks, bags, ubolts as add ons. Still not in full production, but its started and getting better. These photos show the new custom front cross member (black frame is not). It will give you ultimate adjustment.
This system has and instant center, where most do not. Everything bolts on. Bag behind axle, sleeve bags must be used (may offer them also) Comes with shock mounts (may offer shocks also as well). Lower bars are 1.75". Uppers are 1.5" Very beefy setup. Does not come with notch, but I can offer a 3" c notch shown here for 150 shipped. This setup should lay 27" tire at 4" off frame. Must use a rear mounted fuel tank, which I offer a kit for that shown here. Current version will be for GM rear ends and most 8.8 Ford that are not extremely off set. (most rear ends have some off set) Will have a zr2 options hopefully be end of 2025. Uses all custom bushings. FULLY bolts on.
I will also have air tank brackets (that can be used with my inner bed brackets). Also I offer compressor brackets, shown here. Those will be $120 shipped. Frame boxing plates are another item I offer as well. Some are on store page now.
If running anything over 28" tall, I will have to modify the lower bar some. The bags are compressing as far as they can go with this notch. Anything more, the weight would be on compressed bags (should be something I'll address anyway)
Shipping will vary. It will go in 4 boxes. Most initial quotes from PA to states even to UT or CA cost range from 175-250$ depending on location. We can email a final invoice with accurate shipping costs.
One of the pictures shows the coil over version (just don't have the coil overs on) and the ford 8.8 differential bracket.
The finished chassis is using all my parts I offer, control arms, 4 link, swap kit, compressor brackets, air tank brackets, raised bed brackets, rear fuel tank kit. This chassis was done up by MAD rides out of Ohio. It has been sold and waiting for the body to be swapped over.
Email if you want on production list.
S10_C NOTCH _bolt on
Made to order. These are about a 3" notch. They should allow up to 27.5" tall tire to lay boards at my 4" off frame setting. (Body off s10 frame height). You will possibly need to duhump lower control arms if running 28+ tall tires, unless you drop down to my 3" off frame setting. Made with 1/4 and 3/16 steel. USA. No hardware included. I have shipped for $150 despite the high steel prices. Typically in stock, email if not on site [email protected]
Here is install video. This is for a longbed frame. If you have a shortbed that was extended to 117" wb and or an extended cab s10 shortened to 117" wheelbase you won't have to move notch forward as much. I would recommend maybe 1/2".
Rear Cross Member AD S10 swap
Rear Cross member only $150 shipped, in stock. 11g USA steel. Bolts to frame. NO hardware included. This is rear crossmember only, for s10 frame.
IF BUYING THIS TO DO A REAR FUEL TANK SETUP, FOLLOW THIS LINK TO PURCHASE THE REAR FUEL TANK KIT, WHICH WILL COME WITH THIS CROSSMEMBER #RFTANK-S1O. DO NOT ADD THIS TO CART IF YOU ARE DOING REAR FUEL TANK KIT, THAT WILL COME WITH THIS CROSSMEMBER.
https://www.coffeeandcustoms.com/store/p35/Rear_Fuel_Tank_kit_S10_4_piece.html
Rear Fuel Tank kit S10_4 piece
*You may have to modify front and trim a little off rear crossmember if using a leaf spring setup. The upper shock towers get very close to my front crossmember. Last two pics will show modified and also explains differences in the 3 variation of s10 frames in the rear.
#RFTANK_S10 is a 4 piece kit that includes the main rear crossmember, a front crossmember and 2 pieces that weld to a tank. Shown here is the (tank not included)
- universal tanks inc 16g. Its their UT-N series Size: 27-3/4" x 17-3/4" x 8-1/2"
Welding is required for this particular setup.
Will have other options where you can utilize factory straps or build your own. This should be able to work with a common blazer 19g tank. That tank is more affordable than tanks inc, but its big and bulky. It also limits you with the side mounting fuel inlet.
This is a newly added item so please email us if stock is out.
PRICE is SHIPPED (in some cases this costs us 50$ to ship)
Compressor Brackets
Sold as a set. Made from 3/16 USA steel. Designed for viaair compressors. Others probably work. Can mount in several locations as seen in photos. Note, you only need compressors if you are running air ride or doing air horns. No hardware included. Price is shipped.
PATCH PANELS_KICKPANEL_SET Click for Details
NOT really pushing these but I can make them. Shipping is biggest factor with them. Price will probably be $30 each plus ship. These are made from 18g steel, shipped flat. You will have to form the bottom to contour with floor. Some trimming may be needed. I prefer no beads in the kick panels and cowls so they fit tight together. With both being 18g there is plenty of strength. NOTE: Pass side needs trimmed if you use the stock heater.
PATCHES_RUNNING BOARD LANDINGS
If out of stock please email, these should have consistent inventory for 2025.
FREE SHIP. Save yourself the headache of making these from scratch. Come in sets of 6. If you want less please contact me directly and I can send you an online invoice.
Made in USA, ships raw
Free sticker
inquire [email protected]
S10 frame boxing plates
Made to Order if out. Lead is a week or less. 11g steel. welding required. Set shown here is for lower part of frame. spans 23" these would be $75 shipped.
Firewall Filler kit (47-55)
Could be used for other applications. 18g punch sheet,with some spare material left for any custom fillers that need made. This should handle most firewalls. Most pieces should be butt weld but some sanding may need required. Or you can lap weld it, up to you. The heater hose fillers will be loose in package, not in the punch sheet. 2 stickers will come with it. Laser cut in house with USA material. IF SOLD OUT, email us. Odds are we have them in stock or can make them that week. Made specifically for the 47-55 Chevy/Gmc trucks. However 47-48 holes are not all the same
There are a few holes in driverside top that I would not fill. They are dash brace holes. What I like to do is paint carriage bolts and put them in to hold that brace. Just have to grind down the square part on the carriage bolt so it can set nice and flush with firewall.
47-48 Chevy AD truck REAR CAB BRACE
You do not need to order these if you order a kit, these will come with them if you have the 47-48 cab, as of 2023. If you orderd a kit prior and didn't get them, you would have to purchase them.
These are 1/8 thick braces that mimick the newer style cab bracing. 47-48 cabs used a center mount rear cab mount. On my kits we prefer 4 corner mounting for all AD trucks. You need to bend about 45 degrees and weld to floor and rocker.
How to tell if you have a 47-48 cab, it will be flat underneath and no shackles from cab to frame. Inside of cab will have this center piece behind seat in middle of cab.
IF SOLD OUT, EMAIL US. USUALLY KEEP THESE IN STOCK FOR KIT ORDERS. THESE ARE FREE IF YOU ORDER A BODY OR FULL KIT. [email protected]
Panza Shop Truck Tee_ Black
- 6-ounce, 100% ring spun cotton, 18 singles
- 90/10 ring spun cotton/poly (Athletic Heather)
- 50/50 ring spun cotton/poly (Heathers)
- Proudly American made
- 1x1 rib knit neck
- Shoulder to shoulder taping
- Set-in sleeves
- Tear-away label
IF sold out I will restock and continue to keep restocking along with quite a few new designs coming 2024. All shirts come with FREE sticker.
PRICE IS SHIPPED TO LOWER 48. INTERNATIONAL ORDERS PLEASE EMAIL ME
[email protected]
thanks
Henry
Panza Shop Truck_Hoody_Tall cut
This is for Tall cut only. Sizing starts at Large and up. These are a nice quality and fit trust me. Tall hoodies are essential IMO, nothing worse than your back hanging out all the time with poorly designed cuts. I will offer this in a heavy weight regular cut also to accommodate for smaller sizes. These do run big, so keep that in mind.
- 9-ounce, 50/50 cotton/poly fleece
- Air jet yarn for softness
- Removable tag for comfort and relabeling
- Two-ply hood
- Imported (will offer special edition USA fleece later)
MAY OR MAY NOT HAVE WOVEN TAG
2 color print on front
Price is shipped (will ship flatrate padded envelope for tracking)
Free Sticker included.
Lower 48 states only, International orders please email me
Thanks and God Bless
TEE_TRADITIONAL
For those who like that traditional 50's vibe! A simple 1color front and back print, just how I like it. NOTE there are two color options. Tan and Athletic heather GREY.
MADE IN USA!
- 6-ounce, 100% ring spun cotton, 18 singles
- 90/10 ring spun cotton/poly (Athletic Heather)
- 50/50 ring spun cotton/poly (Heathers)
- Proudly American made
- 1x1 rib knit neck
- Shoulder to shoulder taping
- Set-in sleeves
- Tear-away label
I am very picky with shirts. Been sourcing and printing tees since 1999. Had my own printshop from 07-22. These are truly a perfect weight and feel. Don't be fooled by industry trends from gildan and next level with the fashion fit tees. The quality just isn't there. Gildan does however make a decent hooded sweatshirt for the price. These shirts cost 2-3x's the amount of most blanks. That being said I feel like this is a shirt you will want to wear. It has that combed cotton feel but some weight to it, so you can wear it to church or work in it, or both! Great fit. God Bless.
IF sold out I will restock and continue to keep restocking along with quite a few new designs coming 2024. All shirts come with FREE sticker.
Tee_Coffee shop_Black
Not your average tee here. Get this great fitting USA made tee. 1 color front 3 color back print using a discharge waterbase ink for a no feel touch. Mens cut.
- 6-ounce, 100% ring spun cotton, 18 singles
- 90/10 ring spun cotton/poly (Athletic Heather)
- 50/50 ring spun cotton/poly (Heathers)
- Proudly American made
- 1x1 rib knit neck
- Shoulder to shoulder taping
- Set-in sleeves
- Tear-away label
IF sold out I will restock and continue to keep restocking along with quite a few new designs coming 2024. All shirts come with FREE sticker.
PRICE IS SHIPPED TO LOWER 48. INTERNATIONAL ORDERS PLEASE EMAIL ME
[email protected]
Hats
Richardson brand. I have curved bill and flat bill. Wide variety of colors and designs. Please email if interested. $30 plus shipping.